![vpn tunnel mikrotik client to site vpn tunnel mikrotik client to site](https://help.ui.com/hc/article_attachments/360031167713/topology.png)
#VPN TUNNEL MIKROTIK CLIENT TO SITE CODE#
insert the code itself from dns.he.net we got in the form of a binding dyndns and records, and set our domain as the hostname. Go to painl management tunelem the Advanced tab. Important! To register first you have all five, then it is necessary to remove ns1.
![vpn tunnel mikrotik client to site vpn tunnel mikrotik client to site](https://schroederdennis.de/wp-content/uploads/2021/01/WG-site-to-site.png)
Prescription at the Registrar's NS-servers hurricane for our domain. next, take for yourself a domain (register or take an existing) and go on dns.he.net there are registered and follow the instructions to add our domain, we prescribe for him A and AAAA records, they are putting minimum TTL, mark that they are available for dyndns service code which you can see copied. on there is a script that will help you to work as dyndns (i.e. Как это - register and get a 6in4 tunnel for ipv6. Reservations - check-gateway=ping gateway ISP.Īfter setting up (thanks dannyzubarev), the router responds to the interface on which the request arrives:Īdd chain=input in-interface=wan1-out action=mark-connection new-connection-mark=wan1Īdd chain=input in-interface=wan2-out action=mark-connection new-connection-mark=wan2Īdd chain=output connection-mark=wan1 action=mark-routing new-routing-mark=wan1Īdd chain=output connection-mark=wan2 action=mark-routing new-routing-mark=wan2Īdd dst-address=0.0.0.0/0 gateway=10.0.0.1 routing-mark=wan1Īdd dst-address=0.0.0.0/0 gateway=10.0.0.2 routing-mark=wan2 Verify correct source NAT rule is dynamically generated when the tunnel is established.There is an office, it is the backup ISP (1 and 2) and have a warehouse in this same situation (ISP 3 and 4). ip ipsec mode-config set src-address-list=local When this is done, we can assign newly created IP/Firewall/Address list to IPSec mode-config configuration. ip firewall address-list add address=192.168.88.78 list=local ip firewall address-list add address=192.168.88.12 list=local To send the traffic of only some IP addresses over the tunnel, you can configure it like this instead: ip firewall address-list add address= list=local To send all the traffic on the network over the tunnel, execute the following commands using the range variable: To verify if the connection is successfully created, execute the following: ip ipsec identity add auth-method=eap eap-methods=eap-mschapv2 generate-policy=port-strict mode-config= peer= policy-template-group= remote-certificate=.pem_0 username= password= ip ipsec peer add address= exchange-mode=ike2 profile= send-initial-contact=yes name="" port=443Ĭreate an IPSec identity using previously set variables for username and password. **Alternatively, if your ISP is blocking ports 5, set peer to use port 443. ip ipsec peer add address= exchange-mode=ike2 profile= send-initial-contact=yes name="" ip ipsec mode-config add responder=no name="" ip ipsec policy add dst-address=0.0.0.0/0 group= proposal= src-address=0.0.0.0/0 template=yes While it is possible to use the default policy template for policy generation, it is better to create a new policy group and template to separate this configuration from any other IPsec configuration. ip ipsec proposal add auth-algorithms=sha256 enc-algorithms=aes-256-cbc pfs-group=ecp521 name="" ip ipsec profile add hash-algorithm=sha512 enc-algorithm=aes-256 dh-group=ecp521 name="" It is advised to create a separate Phase 1 profile and Phase 2 proposal configurations to not interfere with any existing or future IPsec configuration.